Metal 3D Printing in Germany: Exploring Wire and Arc Additive Manufacturing (WAAM)

Share this Article

In the recently published ‘Plasma Multiwire Technology with Alternating Wire Feed for Tailor-Made Material Properties in Wire Arc Additive Manufacturing,’ authors Uwe Reisgen, Rahul Sharma, and Lukas Oster (all from RWTH Aachen University) delve into the finer points of metal 3D printing in large-scale production.

In researching wire and arc additive manufacturing (WAAM), the team of scientists investigates benefits such as in situ alloying, along with methods that employ wire to create new composites.

As the use of functionally graded materials continues to grow—along with research and development—industrial users can look forward to potential in a variety of applications. In this study, the authors sought to fabricate components more efficiently, with more robust mechanical properties.

Taking a more expanded look at the capabilities of FGMs, the authors realized there were many different alloy combinations, to include:

  • Titanium to titanium carbides
  • Iron to iron aluminides
  • Iron or copper-based alloys
  • Nickel-based alloys

With powder-based 3D metal printing proving to be more expensive than wire, WAAM processes could open many new opportunities for users, with the use of high local heat input and high material deposition. Used strictly for the production of metal parts and constrained somewhat by the requirement for complex control processes, WAAM techniques have been used to produce over 200 tons of parts.

Because of the obvious advantages, researchers continue to work on overcoming obstacles, with this most recent research focused on creating FGMs made of steel and nickel alloys, varying individual wire feeding speeds and demonstrating transformed chemical composition between layers.

“For the evaluation of the basic process stability of the plasma multiwire process, a combination of low-alloyed steel (EN ISO 14341-A: G 3Si1) and high-alloyed chromium–nickel steel (EN ISO 14343-A: G 19 9 LSi) was used,” stated the researchers.

“Due to the difference in thermal conductivity, the flow behavior of the liquid molten pool, and the solidification behavior, this material combination is supposed to reveal possible restrictions of the plasma multiwire process.”

The authors relied on two different use cases:

  • Chemically graded tube segments between ferritic steel and austenitic steel
  • Structures of variable tensile strengtjh

Position of the used material combinations in the Schaeffler diagram

 

(a) Basic sketch of the plasma multiwire process; (b) schematic picture of the wire feed speeds during one weldment; (c) alignment of the wires.

All work was completed via the plasma multiwire technique, based on common plasma welding processes with an electric arc burnt between a nonconsumable tungsten electrode and workpiece.

“Multiple wires of different chemical compositions were fed into the molten pool and built the final alloy in situ. The wire feed speed was changed during the running process, while the combined total wire feed speed was always kept constant,” stated the authors.

Three zones were used to represent the samples:

  • Pure material A
  • Transition area from material A to material B
  • Zone of pure material B

With this process, the researchers were able to create chemically graded structures, while noting challenges to be overcome, such as cold cracks produced in case one and case two.

“To a certain range of technically relevant material combinations, the formation of low-ductility phases in the transition area seems inevitable. This leads to the necessity of strategies to improve the fracture behavior despite the existence of low-ductility phases. One possibility of improving the fracture behavior is shifting the transition zones layer-wise along the welding axis so that critical martensitic LDP phases alternate with austenitic higher-ductility phases (HDP).”

Overall, the research team noted that within the three different materials, changes in composition were viable in situ when alternating speeds of the wire feeds during fabrication—opening the potential to creating large-scale, 3D printed metal parts.

(a) Schematic picture of shifted transition zones and location of the test specimen. (b) Fracture behavior of a tensile test sample by alternating high-ductility phases (HDP) with low-ductility phases (LDP).

They also noted that low ductility phases are not always linked to bad structural behavior, along with observing that wires with varying tensile strength ‘showed no critical low-ductility phases.’ Hardness curves demonstrated good mechanical properties, leading the researchers to see real promise in creating customized workpieces.

“Some restrictions, however, need to be considered,” concluded the researchers. “The formation of low-ductility phases may occur, especially for materials with large differences in the chemical composition. Initial experiments have indicated that it might be possible to avoid constraints in structural behavior by controlling the location of low-ductility phases by alternating low-ductility and high-ductility phases through intelligent path planning.

“Future work will adapt the results to easy-to-use CAD-based setting of material properties and perform deeper structural analysis of the multimaterial workpieces produced. Furthermore, the use of LTT alloys linked to an intelligent path-planning strategy will be investigated within the framework of SFB1120.”

As the realm of materials science continues to grow, users on all levels are offering tremendous innovation to the world with metal 3D printing, from refining energy mechanisms to re-creating classic works of art and also continuing to study issues like porosity.

What do you think of this news? Let us know your thoughts! Join the discussion of this and other 3D printing topics at 3DPrintBoard.com.

Detailed view of the additional shielding gas nozzle, equipped with three wire feeding units. In the centre, the plasma welding torch that generates the required molten pool is visible. Although the system allows the feeding of up to three additional wires, all the presented experiments were carried out using only two wires.

[Source / Images: ‘Plasma Multiwire Technology with Alternating Wire Feed for Tailor-Made Material Properties in Wire Arc Additive Manufacturing’]

Share this Article


Recent News

UK Heart Patient Undergoes Rare Surgery for 3D Printed Titanium Sternum

Interview with Edi Weigh of 3D Printing Service FacFox



Categories

3D Design

3D Printed Art

3D Printed Food

3D Printed Guns


You May Also Like

Sponsored

The Do’s and Don’ts of Additive Manufacturing

The best-use cases for 3D printing aren’t always obvious. When designing an object for additive manufacturing, it’s important to keep the limits and benefits of the process in mind. These...

Sponsored

5 Professional Finishing Options for FDM Parts

Despite the advances of other technologies, Fused Deposition Modeling (FDM) remains the go-to 3D printing process for prototypes and simple plastic parts. It’s fast, it’s cheap, and there are thousands...

Sponsored

The Advantages of 3D Printing

In recent years, 3D printers have taken the manufacturing industry by storm. From automobiles to computer parts, products made by 3D printers have undoubtedly played a big role in the...

3D Printing Being Combined with Soldering to Create High-Performance Zeolites

Researchers in China are exploring the use of minerals called zeolites, hoping to harness ‘desirable configurations’ via 3D printing and soldering, which is further outlined in ‘Fabricating Mechanically Robust Binder-Free...


Shop

View our broad assortment of in house and third party products.


Print Services

Subscribe To Our Newsletter

Subscribe To Our Newsletter

Join our mailing list to receive the latest news and updates from our 3DPrint.com.

You have Successfully Subscribed!