Novel Retroflective Fibers Made Through 3D Printing

Share this Article

In ‘Fabrication and measurement of 3D printed retroflective fibers,’ authors Michael Ghebrebrhan, Gabriel Z. J. Loke, and Yoel Fink are engaged in studying novel materials for additive manufacturing processes. With a new retroreflective fiber, the authors offer a material combination with a previously unheard of complex (non-circular, non-convex) cross-section that also exhibits optical scattering properties. This new kind of fiber is built up layer by layer but can subsequently be used as a fiber would.

As thermal drawing becomes more popular again for creating complex fibers, researchers make use of polymers, metals, elastomers, and more. For this research project, they created a 3D printed preform meant to retroreflect light—or as the authors explain, ‘the angle of reflection is the negative of the angle of incidence.’ The preform is made of polymer and metal (polycarbonate (PC) and indium), with the fiber acting as the element that retroreflects light.

a) Top view of the 3D printed polycarbonate (PC) preform with five indium strips in
the channels. The outer cross-section of the preform contains a curvy serpentine outline. b)
Side view of same preform. c) Epoxy-embedded drawn fiber under a microscope (transmitted
light image). d) Same sample but reflected light. Both images in c and d illustrate the same
curvy serpentine indium architecture as that constructed in the preform

“Glass beads on a reflective surface are a familiar example of a retroreflective surface,” state the researchers. “To maximize retroreflectivity, the polymer’s refractive index should be close to 1.9. At that index, a cylinder or sphere will refract light towards the intersection of the optical axis and back surface.”

The preforms were 3D printed on a Stratasys Fortus 450MC printer, with infill at the highest setting as attempts to increase it otherwise failed; the issue with indium is that it is so much more dense than PC, and the preform must be able to resist deformation.

“Hence a print path that traces multiple concentric paths should be used to counteract the outward hydrostatic pressure from the liquid indium for preserving the cross-section and preventing pooling (lumping) of indium in the draw furnace,” state the researchers.

Evolution of 3D printed preform cross-section: 1) two bridges to connect outer ring to inner PC core, 2) five bridges to reinforce outer ring, 3) similar to 2 but reduction of channel volume to reduce indium volume and outwards stress during draw, 4) similar to 3 but with thicker bridges for further reinforcement.

As the researchers worked to stop pooling of indium, they lowered dwell time and maximum temperature as much as possible. They did, however, find that because the preform is 3D printed, strength was not as high as in comparison to a solid rod. Because of that, its viscosity had to be lower than a solid preform—created with a preform that includes a ‘long solid bottom.’

One part of a fiber with five filled channels was then taken for retroreflection. As light was focused on the fiber, the team recorded intensity with a spectrometer.

“As our figure of merit, we calculate the amount of light retroreflected by a single fiber relative to that of a white reflecting standard. Both are then scaled by the intercepted area. This yields a rescaled relative retroreflection ratio (RRR),” concluded the researchers. “Across the visible spectrum we obtain a rescaled RRR of roughly 260.

“Complex cross-section preforms are easily attainable with additive manufacturing and future efforts will explore the addition of multiple materials.”

The study of materials continues to become more complex in 3D printing, and especially with composites—from continuous fiber to wire polymers, flax biocomposite, and countless others. What do you think of this news? Let us know your thoughts! Join the discussion of this and other 3D printing topics at 3DPrintBoard.com.

. a) Ray-trace illustrating retro-reflection. b) RRR versus refractive index of outer
ring. The red line indicates our fiber (n = 1.58, RRR = 260). The peak RRR value occurs for a refractive index just over 1.9.

[Source / Images: ‘Fabrication and measurement of 3D printed retroflective fibers’]

Share this Article


Recent News

How 3D Printing Is Changing Sustainable Housing

Additive Manufacturing Serialization and Tracking



Categories

3D Design

3D Printed Art

3D Printed Food

3D Printed Guns


You May Also Like

3D Printing News Briefs: November 12, 209

In today’s 3D Printing News Briefs, we’re talking a little business, then moving on to some medical news. Volkswagen has achieved a major metal 3D printing milestone with HP, and...

What is Metrology Part 10: Certification

In this article, we are discussing the viability of certifications and how this is especially of new importance within the metrology field.

Interview with Alexandre Donnadieu-Deray of 3YOURMIND

Alexandre Donnadieu-Deray is the Managing Director of the company 3YOURMIND. 3YOURMIND provides software to manage and optimize your end-to-end Additive Manufacturing workflows. There organization gives an interesting value proposition to their end users. They sit in between technical expertise as well as customer service.

3D Printing News Briefs: April 21, 2019

We’re beginning with an aerospace 3D printing story in 3D Printing News Briefs today, then moving on to news about some upcoming industry events and finishing with a little business....


Shop

View our broad assortment of in house and third party products.


Services & Data

Subscribe To Our Newsletter

Subscribe To Our Newsletter

Join our mailing list to receive the latest news and updates from our 3DPrint.com.

You have Successfully Subscribed!